![savage xr lan cfg savage xr lan cfg](http://1.bp.blogspot.com/-gTIpBZbWChE/UQsgAw7fVLI/AAAAAAAAAaI/p5F1XOPg6Nc/s1600/5+WS-C2960-24TC-L.jpg)
When the controller is in WAN-PHY mode the WIS sublayer transports 10 Gigabit Ethernet frames in an OC-192c SONET payload which can interoperate with SONET section or line level repeaters.
Savage xr lan cfg serial#
To achieve this compatibility, a WAN Interface Sublayer (WIS) is inserted between the 10 Gigabit Ethernet Physical Coding Sublayer (PCS) and the serial Physical Medium Attachment sublayer/Physical Medium Dependent sublayer (PMA/PMD). The purpose of WAN-PHY is to render 10 Gigabit Ethernet compatible with the SONET STS-192c format and data rate, as defined by ANSI, as well as the SDH VC-4-64c container specified by ITU. Between devices (LTE - Line Terminating Equipment or STE - Section Terminating Equipment), the endpoints can be an Add-Drop Multiplexer (ADM) or Dense Wavelength Division Multiplexing (DWDM) OC-192c POS interfaces. WAN-PHY will not interoperate and terminate on a PoS (Packet over Sonet) or EoS (Ethernet over Sonet) port. When deploying Ethernet WAN interfaces as endpoints or PTE between routers, the other endpoint must be an Ethernet WAN interface. WAN-PHY controllers can only be used as Path Terminating Equipment (PTE).
Savage xr lan cfg software#
LAN/WAN-PHY support in Cisco IOS XR software is based on the IEEE 802.3ae standard.
![savage xr lan cfg savage xr lan cfg](https://i.ytimg.com/vi/wDGn93hedcs/maxresdefault.jpg)
– 20-Port 10-Gigabit Ethernet LAN/WAN-PHY PLIM Information About the LAN/WAN-PHY Controllers The default mode of the LAN/WAN-PHY controller is LAN mode for the following SPAs:
Savage xr lan cfg how to#
How to Configure LAN/WAN-PHY Controllers.Information About the LAN/WAN-PHY Controllers.Prerequisites for Configuring LAN/WAN-PHY Controller Interfaces.8-Port 10-Gigabit Ethernet LAN/WAN-PHY PLIM (8-10GBE-WL-XFP).4-Port 10-Gigabit Ethernet LAN/WAN-PHY PLIM (4-10GBE-WL-XFP).Support was added for the following PLIMs:
![savage xr lan cfg savage xr lan cfg](https://www.cisco.com/c/dam/en/us/td/i/200001-300000/250001-260000/253001-254000/253448.eps/_jcr_content/renditions/253448.jpg)
20-Port 10-Gigabit Ethernet LAN/WAN-PHY PLIM (20X10GBE-WL-XFP) (with the Cisco CRS-3 Modular Services Card or Cisco CRS-3 Forwarding Processor Card).14-Port 10-Gigabit Ethernet LAN/WAN-PHY PLIM (14X10GBE-WL-XFP) (with the Cisco CRS-3 Modular Services Card or Cisco CRS-3 Forwarding Processor Card).Support was added for the following physical layer interface modules (PLIMs): Support was added for user configuration of WAN-PHY Signal Failure (SF) and Signal Degrade (SD) Bit Error Rate (BER) reporting and thresholds. Support was added for the 1-Port 10-Gigabit Ethernet LAN/WAN-PHY Shared Port Adapter (SPA-1X10GE-WL-V2). This feature was introduced on the Cisco CRS-1 Router. This module describes the configuration of LAN/WAN-PHY controllers on the Cisco CRS-1 Router.įeature History for Configuring LAN/WAN-PHY Controller Interfaces Configuring LAN/WAN-PHY Controllers on Cisco IOS XR Software